B-Stock! Demo unit with original package and full warranty!

Dark Energy III is a fully analog monophonic synthesizer with Midi and USB interface.
Essentially it's an enhanced version of the Dark Energy II. These are the main differences between Dark Energy II and III:

• VCO has in addition the triangle waveform available
• no heat-up period of the VCO
• min. eight octaves perfect 1V/octave tracking of the VCO
• separate reset inputs for the two LFOs
• improved ADSR
• access to additional functions via pin headers inside the unit for DIY modifications (e.g. linear FM, hard/soft sync)

The filter is the same as the Dark Energy II and all other not mentioned functions are the same compared to Dark Energy II

VCAs are the cornerstones of modular patches: shaping the amplitude or timbre of a tone with an envelope, animating a mixture of several oscillators, controlling the amount of filter modulation with a random source or a touch controller, applying an envelope on the linear FM signal hitting an oscillator... are all possible uses of these super versatile building blocks. That’s why you never have enough of them. What about four more?

Veils provides four VCAs with an adjustable response curve. Veils’ outputs are daisy-chained, allowing adjacent groups of 2, 3, or all 4 channels, to be mixed together.

All inputs DC-coupled.
All inputs handle audio-rate signals.
Input impedance: 100k for all inputs.
Gain scale: a +5V CV translates to a gain of 1 (0dB).
Gain range: 2 (+6dB) in linear operation, 10 (+20dB) in exponential operation.
10 HP.
Current consumption: +12V: 50mA ; -12V: 50mA.

Inamp is a dual pre-amp in just 4 HP. Featuring 6,3 Jacks inputs as well as Minijacks. Both inputs are summed so you can use them at the same time as an input mixer.

The unit is designed to amplify up to x20 the input signal, allowing to amplify most of the music machines out there (Domestic line levels) as well as some guitars (Hum bucket-like pickups and so).

STMix is a compact 4 channel stereo mixer with an auxiliar input. This input will allow us to chain a few of them or to insert an extra fifth input.
This module is compatible with the Hexmix System, and can be internally connected to Hexmix module to add the output of STMix to your main mix.

Features

• Four channels stereo inputs with volume control
• Aux input straight to the Mix out
• Input Impedance selector
• Level meter LEDs
• Connector in the back to interface with Hexmix module.

CV Thing is a fully mappable CV to MIDI converter in just 6HP. Its based on the VCMC module, but aiming for small and compact performance rigs. It has eight inputs that can be mapped to any MIDI message quite easily thanks to its simple and intuitive user interface. CCs, Program change ,V/Oct to Note or Clock are some of the messages that can be configured to easily control MIDI gear from your modular rig.

Features

• Class-compliant USB MIDI and TRS connectors.
• TRS to DIN5 adaptor included.
• 8 CV inputs.
• Controls fully mappable to any MIDI message (CC, Notes, Program change, Clock, ST/SP, NRPN...)
• Configurations saved both in internal memory and via Sysex.

100 pieces of the unique screws designed specifically for Eurorack. These M3 screws can be secured by hand, all common screwdrivers and Allen Key. These are great for saving time when rearranging your synth.

Each Knurlie comes with a fitted plastic washer to prevent rack rash.

Running Order is a two track trigger sequencer:
It can be a precise master clock or manipulate incoming clock signal and works great in use as a sub-sequencer/divider in your Eurorack environment.

• 6 HP width, 30 mm depth (with plugged ribbon cable), power requirements: +12V: 30mA, -12V: 10 mA
• Zero-jitter clock generation: less than 50 microseconds internal clock jitter
• 101 style 1/16th note input mode (step/rest) with manual or CV controllable amount of triggers repeats when the active trigger step happens
• Euclidean mode enabled for each tracks where we set Euclidean total steps amount in the circle and then amount of triggers happening in that circle,
• Separate synchronization (reset) inputs, sync for track 1 is normalled to sync track 2
• Clock divider for incoming external clock allows to quickly obtain various musical divisions on the fly incl. triplets of course but more importantly tuplets mode allows to stretch desired amount of triggers happening into a single bar
• Separate mute buttons for each track
• 8 patterns of triggers sequences stored in the module and recalled on the next power on

The Tessitura Tailor adds or substracts a precise voltage (from -2 to +2 volts) to the signal received at the CV input. This signal is transposed by octaves, depending on the rotary switch’s position. As the CV input is normalised to 0 volt, the module works without any input as an octave switch.

• Switchable CV transposer/generator
• Stepped potentiometer allowing transposition from -2 to +2 octaves
• Precison trimmer at the back of the module for fine-tunning.
• Skiff friendly (25mm deep)
• Intellijel and Pulp Logic format supported
• 1U � 10hp

The Time Apprentice is a compact dual configurable clock divider. The dividers have their own set of divisions, perfect for applications such as clocking and resetting sequencers, syncing pingable modulation sources or triggering events. A set of jumpers at the back of the module allows for personalisation of the divider’s behaviour.

Features

• Dual clock dividers
• Dedicated potentiometer for each divider with two different ratio ranges
• 4 jumpers at the back allowing customisation of the dividers (triggers/gates, auto-reset, alternative clocking)
• Skiff friendly (25mm deep)
• Intellijel and Pulp Logic format supported
• 1U � 14hp

Module A-138n is a simple four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator available. The output is twice available (two sockets, hard-wired like a multiple).

HP : 4

AUDIO to VIDEO VOLTAGE CONVERTER

this module takes any input voltage and divides it by 5. the main operation is to convert eurorack audio modules down to the 1volt LZX video range.

pairs well with eurorack audio modules, envelopes, lfos, oscillators.

CVB001 is based on a modified video enhancer circuit and is the Eurorack version of the CBV001S. It generates color and distortion effects and has a CV input that allows control from DC signal to video rate.

– 12HP
– 30mA +12V
– 0mA -12V
– 0mA +5V
– 25mm deep

Attention! Building DIY kits happens on your own risk. We can't do support or give a guarantee for correct function, because that depends on your own skills. Be responsible and check the building instructions before you buy. Thank you!

Quad inverter, invert the signal while keeping it between 0-1V.

Inputs: 0-1V, 100kohms
Outputs: 0-1V, 499 ohms

– 4HP
– 17mA +12V
– 17mA -12V
– 0mA +5V
– 40mm deep

Attention! Building DIY kits happens on your own risk. We can't do support or give a guarantee for correct function, because that depends on your own skills. Be responsible and check the building instructions before you buy. Thank you!

Component/YPbPr to 1V RGB colorspace converter, to process a component video source into a video system.
Only works with interlaced SD component.

Inputs: 0-700mV YPbPr, 75 ohms, RCA
Outputs: 0-1V RGB, 499 ohms, jack

– 4HP
– 28mA +12V
– 16mA -12V
– 0mA +5V
– 50mm deep

Attention! Building DIY kits happens on your own risk. We can't do support or give a guarantee for correct function, because that depends on your own skills. Be responsible and check the building instructions before you buy. Thank you!

Quad frequency doubler, each stage double the signal frequency and are chained together to multiply the signal at the input by 16. Switching jacks allow to break the connection between each stage to use them individually.
One stage can be used to:

• convert a ramp/saw signal to triangle signal
• multiply a triangle signal by a factor of 2
• multiply a sine signal by a factor of 2 (output sine is glitched)
• solarize a video signal

Inputs: 0-1V, 100kohms
Outputs: 0-1V, 499 ohms

– 4HP
– 38mA +12V
– 37mA -12V
– 0mA +5V
– 50mm deep

Attention! Building DIY kits happens on your own risk. We can't do support or give a guarantee for correct function, because that depends on your own skills. Be responsible and check the building instructions before you buy. Thank you!

Quad distribution amplifier in Eurorack format, to distribute composite video signal to up to 4 monitors.
An internal connector allows internal sync to be distributed to the 4 ouputs to share sync to other systems, internal or external signal distribution is set using a jumper. Another jumper is used for termination of the internal sync signal if required. This module doesn’t need sync to operate.

– 4HP
– 40mA +12V
– 4mA -12V
– 0mA +5V
– 40mm deep

Attention! Building DIY kits happens on your own risk. We can't do support or give a guarantee for correct function, because that depends on your own skills. Be responsible and check the building instructions before you buy. Thank you!

Quad inverter, invert the signal while keeping it between 0-1V.

Inputs: 0-1V, 100kohms
Outputs: 0-1V, 499 ohms

– 4HP
– 17mA +12V
– 17mA -12V
– 0mA +5V
– 40mm deep

Component/YPbPr to 1V RGB colorspace converter, to process a component video source into a video system.
Only works with interlaced SD component.

Inputs: 0-700mV YPbPr, 75 ohms, RCA
Outputs: 0-1V RGB, 499 ohms, jack

– 4HP
– 28mA +12V
– 16mA -12V
– 0mA +5V
– 50mm deep

Quad frequency doubler, each stage double the signal frequency and are chained together to multiply the signal at the input by 16. Switching jacks allow to break the connection between each stage to use them individually.
One stage can be used to:

• convert a ramp/saw signal to triangle signal
• multiply a triangle signal by a factor of 2
• multiply a sine signal by a factor of 2 (output sine is glitched)
• solarize a video signal

Inputs: 0-1V, 100kohms
Outputs: 0-1V, 499 ohms

– 4HP
– 38mA +12V
– 37mA -12V
– 0mA +5V
– 50mm deep

Quad distribution amplifier in Eurorack format, to distribute composite video signal to up to 4 monitors.
An internal connector allows internal sync to be distributed to the 4 ouputs to share sync to other systems, internal or external signal distribution is set using a jumper. Another jumper is used for termination of the internal sync signal if required. This module doesn’t need sync to operate.

– 4HP
– 40mA +12V
– 4mA -12V
– 0mA +5V
– 40mm deep

CVB001 is based on a modified video enhancer circuit and is the Eurorack version of the CBV001S. It generates color and distortion effects and has a CV input that allows control from DC signal to video rate.

– 12HP
– 30mA +12V
– 0mA -12V
– 0mA +5V
– 25mm deep

CVB001S is based on a modified video enhancer circuit and is the standalone version of CBV001. It creates color and distortion effects and features a CV input, allowing control from DC signal up to video rate.

Power Supply is included.

TRQ is based on a color inverter circuit. Base circuit can invert the content of a composite video signal, and wipe between original and inverted video, with independent gain control on original and inverted signal. TRQ adds a second wipe, with a CV/audio input so the wipe(s) can be controlled with an external signal. This signal can be processed using the internal sample and hold, an internal clock is provided, however an external clock signal can be used. TRQ also features 2 glitch switches, with a potentiometer for effect level, and an 8 position rotary switch to set intensity of the effect.

– Video input: composite 75 Ω / 1vpp RCA
– Video output: composite 75 Ω / 1Vpp RCA
– CV/Audio input: x10 gain to accomodate with low sound sources, louder sources can be attenuated using the attenuator.
– Clock input: +5V clock signal
– 5 toggle switches: Single/Dual Wipe, CV/Sampe and Hold, FX1, FX2, ON/OFF
– 1 rotary switches: FX Intensity
– 7 potentiometers: WIPE A, WIPE B, CV LEVEL, CLK RATE, GAIN, GAIN INV, FX LEVEL

The MeloDICER is Vermona's vision of a sequencer with the perfect balance between stochastic and deterministic creation of rhythm and melody. Its algorithms generate random values that magically turn into musical events.

It can generate its own tempo using the TAP button or it can be synced to an external clock source.

The rhythm section has four controls labelled with Note Value, Variation, Legato and Rest, allowing to manipulate the length of the notes, their duration and placement in the pattern. With the Rest knob, the meloDICER randomly adds musical rests to the pattern.

The semitone probability faders which are labelled from C to B set the probability for each semitone to appear in the pattern. As a visual support, the faders’ LED goes on for the duration of the corresponding note.

The overall output range of the meloDICER is up to five octaves which is controlled by the two Range faders, allowing to set the lowest and highest note separately.

With each press on the DICE buttons, the meloDICER generates new random values for the rhythm respectively the melody section. We call that behavior dice-mode. The counterpart of dice-mode is realtime-mode. Press and hold one or both DICE buttons for a second until the corresponding LED goes off. In realtime-mode, there is no repeated pattern. MeloDICER continuously generates new random values, based on the parameters you set for the corresponding section.

The encoder allows to control the pattern length by setting the first and last step, and to store up to 16 patterns.

The module also offers two CV inputs and two gate inputs for controlling various parameters.

Furthermore, the Melodicer features two quantizer modes, allowing to work as quantizer for external CV signals. The faders of the melody section define the scale.

Power consumption: 150mA at +12 V and 50mA at -12 V

Depth: 25mm

HP : 34